RC Waving Flags Decals
RC Waving Flags Decals
 |
No items matching your keywords were found.
_________________________________________________________________________________
|
|
Exceed RC Mirage 2000 64MM EDF Jet * Receiver-Ready Version * $299.95 This is a Receiver-Ready Mirage 2000 64MM EDF Jet. User is required to have their own TX+RX. Wingspan: 575mm Length: 830mm Flying Weight: 520g Three 9 gram servos Brushless Powered: Powerful 14L inner runner brushless motor and 25A ESC Battery: 3 Cell Li-Po Battery,1300 mAh,11.1V Additional Requirements: Radio System: 4Ch Tx and 6 Ch Rx, Exceed RC has now shrunk this fighter jet so you can fly at your own hands. The Exceed Rc Mirage 2000 Lighting Red Series is made with high performance Ducted Fan, Receiver-Ready right out of the box with minimum assembly required. Exceed RC Mirage 2000 is powered by the new developed 14L inner runner brushless motor with 25A ESC electric speed controller. The Exceed RC Mirage 2000 Lighting Red Series RTF Scale Jet is an all-molded foam airplane that comes completely painted in an attractive matte finish with waterslide decals applied. The 64mm fan with brushless inner runner motor is pre-installed, as is the 25A brushless speed control. The jet has 3 preinstalled servos. Landing gear is fixed but can be easily removed for hand launching. Battery changes are quick, just remove the hatch and place it in. The Exceed RC Mirage 2000 jet is large enough for good visibility in flight, but is easily transported. The thrush from the 64mm fan with the included 3 cell Li-po Battery 1300 mAh 11.1V will quickly accelerate the Exceed RC Mirage 2000 Jet into the air. The climb out is steep and the speed impressive. The full scale Mirage 2000 had the glide angel of a brick; our version display much more pilot friendly manners. Due to its light weight, the Mirage 2000 flying character, making landings a thing of beauty. Flight times are about 10 on a charge. |
|
|
WS019 PWC decals $33.99 WS019 PWC decals RC cars are a fantastic hobby, but everyone crashes now and then. Don't feel bad as once you get the hang of driving an RC car your life will never be the same. Your RC world will be filled with the joys of driving RC cars on the track, block, backyard, or parking lot. Make sure to check out our wide assortment of nitro RC cars featured at our toy stores that make for high speed fun. We carry all Cen parts too. Spare parts for remote control cars are inexpensive, but driving an RC car with a miniature camera is priceless. Our mini camera is extremely light in weight and size so there is no need to worry about extra pounds. All of our remote control cars are more than powerful enough to lift the mini cameras we offer as it only weighs a few grams. |
|
|
CMPro Sky 182-50 Nitro RC Plane ARF *Brand New* $299 The new CMPro Sky 50-182 ARF features nicely painted fiberglass components with decals already applied and clear coated. Finished with fine detailing, you could almost believe that you were looking at the real thing. If you are looking for a small but outstanding scale aircraft, the CMPro Sky-182 50 ARF will not disappoint! Wingspan 1650mm Length 1250mm Weight 2950~3100g Wing Loading 81~85 dm/2 Airfoil Naca2412 Wing Area 36.5 dm/2 Radio Control 5 Ch 7 Servos purchase separately 2 Strok Engine 46~50 purchase separately 4 Strok Engine 52~63 purchase separately |
|
|
CMP P40 Warhawk 50 - 54" Nitro Gas ARF Radio Remote Controlled RC Airplane RC "Tiger Shark" Plane $299 This P40 Warhawk has a fiberglass fuselage and cowl painted in vague colors. The rib wings are covered with Solartex and airbrushed to match the color of the whole aircraft. The wood that makes up both the wings and the fuselage are all laser cut. The high precision of fiberglass and fine painting work make this kit an extremely realistic aircraft. It is a perfect combination between scale looks and excellent flying performance. The kit comes with a full color decal sheet, wheels and a fuel tank. This war bird is a must fly! What the Pro says! Just to clear up some confusion, and a lot of misinformation on the internet...CMP is not Willhobby, or FlyModel, or any other company. CMP is thier own company, and they have been around for while. I have built a few of their planes, and found the quality to be quite exceptional, they are high-end stuff, and from a scale point of view, nobody else comes close. The P-40, from a scale aspect, blows away the Hangar 9 and everybody else's P-40. The paint job is dead flat and perfect, and there are a ton of factory-installed water transfer decals, a beautiful glass belly tank, strut covers, prepainted canopy frame, lots of nice stuff. All the hardware is exceptional, too, with a fiberglass pushrod for the elevator, and a pull-pull system for the rudder. You need to be careful flying it, though. It has no washout, it's not light, and it will tip stall if you pull too hard or get too slow. The big problem, though, is that the CG in the manual is actually for the much larger 71" one, and will leave you very tailheavy if you don't correct it to about 85mm from the LE. It's really, really important. If you fly off grass, you will have really hard time finding rotating retracts that will hold up. Seriously consider fixed gear like I used. I flew mine with a Saito 62, fit perfectly and was plenty of power. Let's here some other comments, this is a beautiful plane.. For more reviews and comments on other NitroPlanes.com products by rc enthusiasts, click here. *RETRACT NOTE* The retract bays are built into the wing from the factory, so the retracts will drop right in. Wing Span: 53.5" Weight: 5.64lb Length: 46" Wing Loading: 26.97oz./sq.ft. Wing Area: 480sq.in Engine 2c 40~46, 4c 52~63 Radio 4~5 Channel 5~6 Servos The kit box is nice packed, with all the major parts well packed in a light foam wrap and clear plastic bags. All wood rib wing, nicely covered, rivets decals already applied, ailerons hinged and installed. Horizontal, elevators and rudder also all wood, air foiled surfaces, hinged and ready. Fuselage is very detailed with panel lines molded in, glass work is outstanding. Tiger mouth decal, dashboard decal and many others perfectly applied. Drop tank included and assembled. Slots in the interior cardboard held all items tightly |
|
|
Exceed RC F-4E Phantom ARF 64mm EDF RC Jet (without Transmitter & Receiver) $249.95 F-4E Phantom Electric Ducted Fan Radio Control Jet ALMOST-READY-TO-FLY-VERSION WITHOUT TRANSMITTER+RECEIVER Factory Flight Test F-4E Review & Flight Features: -State of the Art Foam -Fully Proportional Elevator, Rudder and Throttle Controls -Improved Aerodynamic with innovative Wing and Fuselage Design -Durable Fuselage and Wings Construction -Easy to learn for Beginner and Fun to Fly for Experts This is the latest creation from the fertile mind of genius EDF designer Andy Chen...there IS a difference as to who designs these, this guy just has the magic touch, and it shows in the scale accuracy of the overall plane, and also in a lot of thoughtful little details and engineering that really make it stand out from the competition. It's beautiful! Small, and very high performance...Very high quality molding, lots of detail, good paint, good water transfer decals, clear canopy with cockpit deck(the pics on the nitroplanes website show an early prototype with a tinted canopy), easily removeable or replaceable landing gear, full flying stab, easy fan access for maintanance, lots of nice features. In the air, it's pure dynamite, everybody guesses it to be about 70mph, and that's very fast for such a small airplane! It's a whole level of performance above the rest of the RTF EDF jets... It's basically the smallest airframe that you can wrap around a 64mm fan. Hand launching is really easy, there is a grip molded in for doing it, and you don't need to heave it, it will fly away from just a light toss with no problems. Roll rate is tremendous, vertical performance is awesome, and downright speed, well...most EDFs, you fly around at full bore all the time, with this one, you want to save full throttle for verticals and high speed passes, and throttle back to half or two thirds to keep the thing manageable the rest of the time, it's mighty quick. It's very easy to land, I have been bellying mine in on the grass with no problems, though you might want to put a little glass cloth on the lower lip of the intakes, they tend to snag the grass and get chipped up. With the landing gear on, off pavement, it has no bad habits at all. The gear comes on and off with a few screws in a minute or two. It takes up no room in the car, it can fly out of small parks, or you can take it to the club field and mix it up with the big boys, it costs little, it requires no maintainance, it looks great, and it flies great. It's my new favorite airplane! Wingspan: 542mm Length: 788mm Flying Weight: 540g Wing Area: 8dm^2 Wing Load: 67g/dm^2 64mm Ducted Fan Servos : 4 9G Servos Motor : 14L inner brushless motor ESC : 25A Battery : 11.1V 1300mAH LiPo Battery Radio System REQUIRED : 4-Channel TX and 6CH Rx |
|
|
Exceed RC F-4E Phantom ARF 64mm Electric Ducted Fan RC Jet Shark Version (without Transmitter & Receiver) $249.95 F-4E Phantom Electric Ducted Fan Radio Control Jet ALMOST-READY-TO-FLY-VERSION WITHOUT TRANSMITTER+RECEIVER Factory Flight Test F-4E Review & Flight Features: -State of the Art Foam -Fully Proportional Elevator, Rudder and Throttle Controls -Improved Aerodynamic with innovative Wing and Fuselage Design -Durable Fuselage and Wings Construction -Easy to learn for Beginner and Fun to Fly for Experts This is the latest creation from the fertile mind of genius EDF designer Andy Chen...there IS a difference as to who designs these, this guy just has the magic touch, and it shows in the scale accuracy of the overall plane, and also in a lot of thoughtful little details and engineering that really make it stand out from the competition. It's beautiful! Small, and very high performance...Very high quality molding, lots of detail, good paint, good water transfer decals, clear canopy with cockpit deck(the pics on the nitroplanes website show an early prototype with a tinted canopy), easily removeable or replaceable landing gear, full flying stab, easy fan access for maintanance, lots of nice features. In the air, it's pure dynamite, everybody guesses it to be about 70mph, and that's very fast for such a small airplane! It's a whole level of performance above the rest of the RTF EDF jets... It's basically the smallest airframe that you can wrap around a 64mm fan. Hand launching is really easy, there is a grip molded in for doing it, and you don't need to heave it, it will fly away from just a light toss with no problems. Roll rate is tremendous, vertical performance is awesome, and downright speed, well...most EDFs, you fly around at full bore all the time, with this one, you want to save full throttle for verticals and high speed passes, and throttle back to half or two thirds to keep the thing manageable the rest of the time, it's mighty quick. It's very easy to land, I have been bellying mine in on the grass with no problems, though you might want to put a little glass cloth on the lower lip of the intakes, they tend to snag the grass and get chipped up. With the landing gear on, off pavement, it has no bad habits at all. The gear comes on and off with a few screws in a minute or two. It takes up no room in the car, it can fly out of small parks, or you can take it to the club field and mix it up with the big boys, it costs little, it requires no maintainance, it looks great, and it flies great. It's my new favorite airplane! Wingspan: 542mm Length: 788mm Flying Weight: 540g Wing Area: 8dm^2 Wing Load: 67g/dm^2 64mm Ducted Fan Servos : 4 9G Servos Motor : 14L inner brushless motor ESC : 25A Battery : 11.1V 1300mAH LiPo Battery Radio System REQUIRED : 4-Channel TX and 6CH Rx |
|
|
U.S. Army P-51D Mustang 50 - 53" Nitro Gas ARF RC Radio Remote Controlled CMPro Plane $299 P51 Mustang 50 - 53" Nitro Gas ARF RC Plane P-51D-Mustang 50 is all laser cut and is a great scale airplane. Featuring pre-covered fuselage and wings with great looking color scheme sure to catch the eye of everyone. The plane comes with fiberglass cowl. Decals are already stuck to the with clear paint on top. Simple assembly of pre-finished parts enable the model to be ready for fly in very short time. Just a few simple jobs installing radio gear, installing engine, etc and you will be flying. With a 4-stroke engine installed, the P-51 Mustang will fly, feel, and sound like a true legendary U.S. Air Force aircraft! *RETRACT NOTE* The retract bays are built into the wing from the factory, so the retracts will drop right in. Wingspan 53" Fuselage Length 46" Recommended Engine Size 2c/40,46 4c/52,63 Flying Weight 6.0 - 6.2 lbs Wing Area 480.6 sq in Airfoil 15% Semi Symmetrical Fuel Tank Spinner The kit box is nice packed, with all the major parts well packed in a light foam wrap and clear plastic bags. All wood rib wing, nicely covered, rivets decals already applied, ailerons hinged and installed. Horizontal, elevators and rudder also all wood, air foiled surfaces, hinged and ready. Fuselage is very detailed with panel lines molded in, glass work is outstanding. US Air Force decal, dashboard decal and many others perfectly applied. Drop tank included and assembled. Slots in the interior cardboard held all items tightly in place, so it will minimize damage from shipping. Included with the kit are fuel tanks, engine mounts, wheels, hardware, pushrods, clear plastic canopy and nose cone, decal sheet, one-piece fiberglass cowls, and fixed wire landing gear plus other necessary hardware. You will need to purchase some building supplies, engines, spinners, servo extensions, and a radio. Mechanical retracts are an interesting option to consider for this plane kit. The quality of the materials is excellent with a one-piece fiberglass fuselage/fin straight and true. The instruction manual has excellent-quality step-by-step drawings. With an 4-stroke engine installed, this P51 Plane will fly, feel, and sound like the legendary Air Force. If you have had a chance to fly the P-51D, you?ll notice how well the design flies for the P-51D. Once in the air, the P-51D Mustang truly shines with its exceptional flight characteristics. The wing loading has been optimized to make it exceptionally nimble and capable of a variety of dif |
|
|
T-28 Trojan - 55" EP-Powered RC Warbird Plane ARF $334.95 T-28 Trojan ARF EP Radio Controlled Warbird Plane The Flying Dream T-28 Trojan comes in a very scale finish and a nicely shaped outline as if you were looking at the real thing. The model consists of a HIP (polystrene) fuselage which is strong and durable, spray painted to a very high standard. Main wings and the tails are balsa-made, factory covered under the new printed-on covering film. All the small details are printed on the film to enhance realistic feelings and it makes the plane a great choice for the scale enthusiasts. The T-28 Trojan is also a scale warbird of outstanding performance. Its large degree of hihedral allows a stable control of the plane and this results in a very smooth flying which you would expect from a Trojan! Wingspan 1400mm Length 1130mm Weight 2300-2400g Wing Loading 71~74 dm/2 Airfoil Naca~0014 Wing Area 32.5 dm/2 Radio Control 4 Ch 4 Servos purchase separately Motors A3520/6~A4120/7 purchase separately ESC 20A~30A purchase separately The well-known T-28 Trojan is presented in a highly visible classic color scheme with good contrasts to make orientation easier during flight. The attractive ready applied decals on the painted fuselage add to the scale look of the model and are protected by a clear-coat for more durable use. The model comes with a 10 wheel, realistic undercarriage giving an extremely steady and straight tracking take off and landing roll. An easily accessed and neat compartment for the battery is featured to help ultra fast installation The fairly close coupled motors make a good choice for your first single engined scale warbird. An ideal fun aircraft for scale enthusiasts. |
|
|
Military EDF Predator UCAV 101mm Electric Ducted Fan RC Airplane $319 The EDF Predator UCAV from Nitro Planes is a large fiberglass jet model with sheeted wings. It comes complete with landing gear, fiberglass canopy, missiles, and all hardware. The model can be powered by a 90mm to 101mm ( 3.5" to 4" ) EDF unit. EDF Predator UCAV 101mm Electric Ducted Fan Airplane Top Features Top quality wood construction with fiberglass fuselage Comes with all hardware and accessories Specifications Wing Span: 47.2 in / 1200mm Wing Area : 521 sq in / 33.8 sq dm Flying Weight : 6.6 lb / 3000 g Fuselage Length : 58.7 / 1490 mm Electronics Required : 4 Channels Radio Transmitter 5 Servos EDF : 101 mm / 4 in Brushless Motor : D36 x L 36 mm 2000 KV Speed Controller : 22.2 V ; 85A Li-poly Battery : 4000 mAh 25 C 22.2 V Click here for UCAV Review/Build Thread The fuselage and parts come well secured in the custom box. All the parts are covered in plastic or bagged. The control surfaces arrive attached with hinge material but need to be CA'ed in place after alignment. The fiberglass canopy is pre-finished and only needs the latch mechanism attached. The landing gear are fixed with a steerable nose wheel assembly. Two sheets of finishing decals are supplied and the 7-page manual, although sparse, provides sufficient photos and text to complete the model by an experienced assembler. Photos A closer look at the fuselage reveals the size, quality finish, construction techniques, and high level of pre-assembly. The T-nuts are already installed, and glued in place, for the gear mains and steerable nose wheel assembly. The battery and servo trays are also pre-installed. Photos Click here for UCAV Review/Build Thread |
|
|
New 2.4GHz F-4E Jolly Roger Phantom EDF Brushless RC Jet 100% Ready-to-Fly $349.95 The F-4E Phantom EDF RC Jet is the latest creation from Exceed RC and there IS a difference as to who designs these, this F4-E jet just has the magic touch, and it shows in the scale accuracy of the overall plane, and also in a lot of thoughtful little details and engineering that really make it stand out from the competition. It's beautiful! Small, and very high performance... Now with 2.4GHz and 100% Ready-to-Fly with Everything Included! This is a truly ready to fly radio controlled airplane that includes everything, including the battery and charger! You DO NOT need to buy anything else! Very high quality molding, lots of detail, good paint, good water transfer decals, clear canopy with cockpit deck, easily removable or replaceable landing gear, full flying stab, easy fan access for maintenance, lots of nice features. In the air, it's pure dynamite, everybody guesses it to be about 70mph, and that's very fast for such a small airplane! It's a whole level of performance above the rest of the RTF EDF jets... It's basically the smallest airframe that you can wrap around a 64mm fan. Hand launching is really easy, there is a grip molded in for doing it, and you don't need to heave it, it will fly away from just a light toss with no problems. Roll rate is tremendous, vertical performance is awesome, and downright speed, well...most EDFs, you fly around at full bore all the time, with this one, you want to save full throttle for verticals and high speed passes, and throttle back to half or two thirds to keep the thing manageable the rest of the time, it's mighty quick. It's very easy to land, I have been bellying mine in on the grass with no problems, though you might want to put a little glass cloth on the lower lip of the intakes, they tend to snag the grass and get chipped up. With the landing gear on, off pavement, it has no bad habits at all. The gear comes on and off with a few screws in a minute or two. It takes up no room in the car, it can fly out of small parks, or you can take it to the club field and mix it up with the big boys, it costs little, it requires no maintainance, it looks great, and it flies great. It's my new favorite airplane! F-4E Review & Flight |
|
|
ARF F-4E Phantom 64mm EDF RC Jet (without TX, RX) $249.95 F-4E Phantom Electric Ducted Fan Radio Control Jet ALMOST-READY-TO-FLY-VERSION WITHOUT TRANSMITTER+RECEIVER Factory Flight Test F-4E Review & Flight This is the latest creation from the fertile mind of genius EDF designer Andy Chen...there IS a difference as to who designs these, this guy just has the magic touch, and it shows in the scale accuracy of the overall plane, and also in a lot of thoughtful little details and engineering that really make it stand out from the competition. It's beautiful! Small, and very high performance...Very high quality molding, lots of detail, good paint, good water transfer decals, clear canopy with cockpit deck(the pics on the nitroplanes website show an early prototype with a tinted canopy), easily removeable or replaceable landing gear, full flying stab, easy fan access for maintanance, lots of nice features. In the air, it's pure dynamite, everybody guesses it to be about 70mph, and that's very fast for such a small airplane! It's a whole level of performance above the rest of the RTF EDF jets... It's basically the smallest airframe that you can wrap around a 64mm fan. Hand launching is really easy, there is a grip molded in for doing it, and you don't need to heave it, it will fly away from just a light toss with no problems. Roll rate is tremendous, vertical performance is awesome, and downright speed, well...most EDFs, you fly around at full bore all the time, with this one, you want to save full throttle for verticals and high speed passes, and throttle back to half or two thirds to keep the thing manageable the rest of the time, it's mighty quick. It's very easy to land, I have been bellying mine in on the grass with no problems, though you might want to put a little glass cloth on the lower lip of the intakes, they tend to snag the grass and get chipped up. With the landing gear on, off pavement, it has no bad habits at all. The gear comes on and off with a few screws in a minute or two. It takes up no room in the car, it can fly out of small parks, or you can take it to the club field and mix it up with the big boys, it costs little, it requires no maintainance, it looks great, and it flies great. It's my new favorite airplane! Features: -State of the Art Foam -Fully Proportional Elevator, Rudder and Throttle Controls -Improved Aerodynamic with innovative Wing and Fuselage Design -Durable Fuselage and Wings Construction -Easy to learn for Beginner and Fun to Fly for Experts Wingspan: 542mm Length: 788mm Flying Weight: 540g Wing Area: 8dm^2 Wing Load: 67g/dm^2 64mm Ducted Fan Servos : 4 9G Servos Motor : 14L inner brushless motor ESC : 25A Battery : 11.1V 1300mAH LiPo Battery Radio System REQUIRED : 4-Channel TX and 6CH Rx |
|
|
Zlin Z-50 Engine 46~52 - 56" Nitro Gas Radio Remote Controlled RC Airplane ARF $319 The Zlin Z-50 is one of the most famous sports planes used in aerobatics and this ARF NitroModel Z50 is built with all the aerodynamic characteristic of the real one! It is a very special aerobatic airplane made by quality balsa wood protected by clear coating. 90% of the model is pre-finished at the factory - you can enjoy flying this beauty with the least building time. And of course, it flies as good as it looks! Wing Span : 55.9 in / 1420mm Wing Area : 531 sq in / 34 sq dm Flying Weight : 5.5lb / 2480g Fuselage length : 43.3 in / 1100mm Engine Required : 2c : 0.46 4c: 0.52 Radio Required : 4channels 5 servos Decals included but not pre-applied. |
|
|
CMP Extra 300s 90 - 65" Acrobatic Radio Remote Controlled Nitro Gas RC Sports Plane ARF $325 The fabulous Extra-330s 90 ARF is pre decorated with an eye catching color scheme. All built-up construction with quality balsa wood which results in a light but strong model. Nicely painted fiberglass cowl and spats. Including with the kit, there are a complete hardware pack and full color decals. You will enjoy flying this model with great delights. Wingspan 65 inch Length 56 inch Weight 3.8~3.9 kg Wing Loading 76~78 dm/2 Airfoil Naca 0014 Wing Area 50 dm/2 Radio Control 4 Ch 5 Servos purchase separately 2 Strok Engine 90 purchase separately 4 Strok Engine 91~120 purchase separately |
|
|
North American AT-6F Texan 160 - 82" Nitro Gas Radio Remote Controlled ARF RC WWII Warbird Airplane $499.95 North American AT-6 Texan 160 - 82" Nitro Gas Radio Remote Controlled ARF RC Airplane The AT-6 Texan ARF Nitro Gas Plane includes decals that are already applied on the fuselage under clear coating for more durable use. This contains a fiberglass fuselage. Wing panel, elevator & tail plane are painted over high-quality balsa wood. The wing section is also fiberglass molded Wingspan 82" Fuselage Length 55" Recommended Engine Size 2c/160 Flying Weight 11.9 lbs - 12.3 lbs Wing Area 1,007 sq in Radio 4~~5 Ch 5~~6 Servos Airfoil NACA 2415 The North American AT-6 Texan won wide acclaim as one of the most well used advanced trainers not only during WWII but also beyond. This specefic AT-6F Texan is a perfect example of this post WWII use as it is restored as and is painted in the colors of the Korean War "Mosquito", a low-level support and target identifier aircraft used to support the faster jets of the period. NitroModels' AT-6 Texan is really popular and can be found at flying field and events in the many regions all over the United States. Do not miss your chance to relive a piece of history! Engine/Radio Equipments Sold Separately. Engine/Radio NOT included. Download Manual Here |
|
|
CMP Blue Extra 330L 50 - 56" Nitro Gas Radio Remote Control Aerobatic RC Aircraft ARF $329.95 The CMPro 50-size Extra-330L (2c 40~46 4c 52~63 ENGINE POWERED AEROBATIC AIRCRAFT) is available in two stunning color schemes.Both come with decals already applied, protected by clear coating. 90% of the model is pre-finished at the factory - you can enjoy flying this beauty with the least building time. And of course, it flies as good as it looks! Wingspan 1430mm Length 1270mm Weight 2.85~2.95 kg Wing Loading 92~95 dm/2 Airfoil Naca 0014 Wing Area 30.8 dm/2 Radio Control 4 Ch 5 Servos purchase separately 2 Strok Engine 40~46 purchase separately 4 Strok Engine 52~63 purchase separately Featuring gorgeous pre-finished parts and complete hardware pack. Comes with optional EP motor mount ? EP or Glow? Make your choice! Plastic engine mount for glow power. Ready covered tailplane and rudder, unique color design to match with the fuselage and wings. Pre painted fiberglass fuselage. Internal construction is nice and neat. Bottom design with attractive color combination. You will never lose this plane from your sight! Light and strong aluminum wing joiner. |
|
|
Mitsubishi A6M5 50 - 54" Nitro Gas Radio Remote Controlled RC Japan Warbird Plane ARF $339 The 50 sized Zero Fighter is the youngest brother from the CMPro Japanese Fighter Series. Featuring a fiberglass moulded fuselage and painted rib wings. A great choice for those war plane enthusiasts. Wingspan 1360mm 53.5" Length 1130mm 44.5" Weight 2.8~2.9 kg 6.17 lb Wing Loading 84~87 dm/2 27.63 oz/sqft Airfoil Naca 2415 Wing Area 33.2 dm/2 514.6 sq in Radio Control 4~5 Ch 5~6 Servos purchase separately 2 Strok Engine 46 purchase separately 4 Strok Engine 50~63 purchase separately Wing Span: 53.5" Weight: 6.171lb Length: 44.5" Wing Loading: 27.63 oz./sq.ft. Wing Area: 514.6sq.in Engine Required: 2c 46, 4c 50~63 Radio Required: 4~5 Channel 5~6 Servos Wing is designed to allow optional retracts fitting A quality hardware pack and full color decals are included. The wing panels and tails are also matt spray painted to increase scale features. The high precision fiberglass fuselage is painted in camouflage finish, making an extremely scale and attractive model. ARF Kit Only. Additional Radio Equipments are required to complete. |
|
|
CMP Zero Fighter 50cc - 80" ARF Nitro Gas Radio Remote Controlled RC Airplane New! $799.95 The Mitsubshi A6M5 52 with wingspan of 2100mm is the biggest brother from the CMPro Japanese Fighter Series. This model, well designed for 40~50cc gas engines, features a fiberglass molded fuselage and painted wing panels. The attention to detail results in an extremely realistic model that flies as look as it looks. Wingspan 2100mm Length 1700mm Weight 6.2~6.5 kg Wing Loading 77~81 dm/2 Airfoil Naca 2415 Wing Area 80 dm/2 Radio Control 5~6 Ch 8~9 Servos purchase separately 2 Strok Engine 40~50 purchase separately The whole aircraft is painted in a matt finish which greatly enhances its scale features. A fixed undercarriage is included while optional retracts fitting is also available. Decals come ready applied and clear coated ? that doesn?t only make the kit more durable but shortens building time as well. A carbon fiber wing tube is included with kit. |
|
|
CMPPro C-160 EP-Powered Twin-Engine RC Scale Plane Almost-Ready-to-Fly $399 TWIN MOTORS POWERED SCALE AIRCRAFT The CMPro EP-C160 features a fiberglass molded fuselage and a built-up wing, ready covered in a classic and attractive color design. The multi wheel landing gear adds a really scale touch to this exciting model. Wingspan 1450mm Length 1178mm Weight 2.5~2.6 kg Wing Loading 113~118 dm/2 Airfoil Torino-26 Wing Area 22 dm/2 Radio Control 4 Ch 4 Servos purchase separately Motors 2213 purchase separately ESC 20A~25A purchase separately The well-known C-160 is presented in a highly visible classic color scheme with good contrasts to make orientation easier during flight. The attractive ready applied decals on the painted fuselage add to the scale look of the model and are protected by a clear-coat for more durable use. The model comes with a 10 wheel, realistic undercarriage giving an extremely steady and straight tracking take off and landing roll. An easily accessed and neat compartment for the battery is featured to help ultra fast installation The fairly close coupled motors make a good choice for your first twin engined scale model. An ideal fun aircraft for scale enthusiasts. |
|
|
Fuel/Electric Red J-3 Piper Cub 15-25 49.6" Radio Remote Controlled RC Airplane $169 Brand New, very adorable 25 class English Red Piper J-3 Cub Grasshopper which reproduces the full-scale aircraft with amazing accuracy, using precise CAD engineering and data from original Piper Cub. Most J-3 Cub ARF are available in 40-class, but this one is slightly smaller and lighter, giving you the option of using a 480 class electric motor instead of using nitro gas. All balsa construction. Aluminum alloy framed cowl. Superb realism and build quality. All major components ready for immediate assembly. Wing Span: 49.6in/1260mm Wing Area: 286sq in/18.6 sqdm Take-off weight: 2.30 lb/1050 g Length: 31.7 in/805 mm Engine: 2 Stroke 15-25 class or 480 electric motor (not included). Radio system required: 4 channel with 4 servos (not included) FEATURES: Intermediate 50" Wingspan. Excellent first sport-scale kit - assembles quickly, maneuvers well and lands slow and easy. Two-piece 25" wings Reproduces the full-scale aircraft with amazing accuracy, using precise CAD engineering and data from original Piper 3-view drawings. Can be flight-ready in 2-3 hours. Lightweight, resistance to scratches, tears and punctures better than most films. Roomy radio compartment simplifies installation of on-board components and provides space to install a fully detailed cockpit and pilot (both optional). Includes an engine mount; great-quality, quality hardware; and decals for authentic markings. Wood wing struts come pre-sanded. The Rare One and ONLY English RED J3 Piper Cub! Awesome!!!! Kit Requires assembly. Can be flight-ready in 3-5 hours |
|
|
New CMP Edge-540T 2c 40~46 4c 52~63 Engine Powered Aerobatic RC Aircraft ( ARF ) $339 Edge-540T 2c 40~46 4c 52~63 Engine Powered Aerobatic Aircraft Edge-540T 50Size The CMPro Edge-540T 50 ARF comes pre-covered in a dazzling color design that will not fail to draw attention. Construction is built-up balsa throughout except for the cowl and spats. This results in a light but strong model. The kit also includes a fiberglass landing gear and polystyrene spats which are strong and durable. All the components are pre-finished and pre-painted at factory to maximum your fun of flying. The kit provides a large area of control surface movements for superb performance: Full aileron design Elevator surface movement approx. 50% Rudder surface movement approx. 60% These features have made our Edge very manoeuverable and thus anymore wishing to try precision aerobatics must not miss this kit! Wingspan 1400mm Length 1270mm Weight 2.8~2.9 kg Wing Loading 90~93 dm/2 Airfoil Naca 0012 Wing Area 31 dm/2 Radio Control 4 Ch 5 Servos purchase separately 2 Strok Engine 40~46 purchase separately 4 Strok Engine 52~63 purchase separately Construction is neat and simple to provide easy access for engine, servo and etc. Quality control horns for direct and more responsive control. Fiberglass landing gears and polystyrene wheel pants, pre-finished at factory. Glass fiber cowl with gorgeous painting. Fuselage is built up by quality balsawood to minimize weight. Wings and tails come pre-covered with decals ready applied, protected by a clear coat. Removable top hatch to provide plenty of room for assembly. All the components |
|
|
|
February 27th, 2005 in
RC Airplanes