RC Knife Foam Cutter
RC Knife Foam Cutter
 |
No items matching your keywords were found.
_________________________________________________________________________________
|
|
AirField 70MM Brushless EDF F-16 Thunderbird Electric Ducted Fan Radio Controlled RC Jet w/ Bombs RTF $399.95 This 70mm F-16 Fighter is a high quality EPS foam model of the famous ?Fighting Falcon?. The F-16 is known as the ?Viper? in US service. It was the first fighter designed to sustain 9g maneuvers. One of the outstanding features is its frameless bubble canopy, which gives excellent all-round vision. The F-16 has been and will remain the multi-role workhorse of the United States Air Force. The F-16 was the main fighter used in the 1991 Gulf War and is still used in today?s ?War on Terror?. The Air National Guard regularly deploys these fighters to the Middle East. In honor of the US Fighters, it is only appropriate that we built these jets with extra care and fine detail. It is painted with an excellent finish to make it look just like the real thing. No details were left out, from the after burner, the missiles, to the predominant nose. To do the F-16 justice, we used the newest electronics and gave it the U.S. Air Force look. Even though we went out of the way to mirror the real F-16, this EDF Jet was also built to be user friendly and ready to fly. The fuselage is pre-assembled and it requires very minimal assembly to get it soaring in the sky. 4 Channel Full Function Radio Controlled (Aileron,Elevator,Rudder,Throttle) Full aerobatic characteristics; inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are possible Excellent hedgehopping performance High speed, flying speed at 80mph+!!! Excellent stability of nosing up and down State of the art components such as Outrunner Brushless Ducted Fan, 45amp Speed Control, and 2200mah 20C 14.8 Volt Li-Po Battery Pack famousus "Cobra Maneuver" available Steerable nose landing gear Rudder helps steer plane on ground on its scale landing gear for easy take off Super tough, lightweight airframe! Shock Resistant Reinforced fuselage and Strong Wings Can Take Off From Ground or Hand Launched Ground Take-Off can be performed easily Excellent Flight Performance Super easy and super stable electric powered scale R/C park flyer for beginner or middle-level users Stable inverted flight fuselage with pre-installed Electronics, Motor, Servos, and Speed Controller Superb Quality, Simply the Best RTF Jet you can find!!! Super stable for beginner, Super low speed for safety, Super low altitude for fun Fabricated by accurate molds with high fidelity of real airplane Excellent stability and aerobatic capability High roll rate Digital |
|
|
AirField 70MM Brushless EDF F-16 Tiger Jet Electric Ducted Fan RC Jet w/ Bombs RTF $399.95 This 70mm F-16 Fighter is a high quality EPS foam model of the famous ?Fighting Falcon?. The F-16 is known as the ?Viper? in US service. It was the first fighter designed to sustain 9g maneuvers. One of the outstanding features is its frameless bubble canopy, which gives excellent all-round vision. The F-16 has been and will remain the multi-role workhorse of the United States Air Force. The F-16 was the main fighter used in the 1991 Gulf War and is still used in today?s ?War on Terror?. The Air National Guard regularly deploys these fighters to the Middle East. In honor of the US Fighters, it is only appropriate that we built these jets with extra care and fine detail. It is painted with an excellent finish to make it look just like the real thing. No details were left out, from the after burner, the missiles, to the predominant nose. To do the F-16 justice, we used the newest electronics and gave it the U.S. Air Force look. Even though we went out of the way to mirror the real F-16, this EDF Jet was also built to be user friendly and ready to fly. The fuselage is pre-assembled and it requires very minimal assembly to get it soaring in the sky. 4 Channel Full Function Radio Controlled (Aileron,Elevator,Rudder,Throttle) Full aerobatic characteristics; inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are possible Excellent hedgehopping performance High speed, flying speed at 80mph+!!! Excellent stability of nosing up and down State of the art components such as Outrunner Brushless Ducted Fan, 45amp Speed Control, and 2200mah 20C 14.8 Volt Li-Po Battery Pack famousus "Cobra Maneuver" available Steerable nose landing gear Rudder helps steer plane on ground on its scale landing gear for easy take off Super tough, lightweight airframe! Shock Resistant Reinforced fuselage and Strong Wings Can Take Off From Ground or Hand Launched Ground Take-Off can be performed easily Excellent Flight Performance Super easy and super stable electric powered scale R/C park flyer for beginner or middle-level users Stable inverted flight fuselage with pre-installed Electronics, Motor, Servos, and Speed Controller Superb Quality, Simply the Best RTF Jet you can find!!! Super stable for beginner, Super low speed for safety, Super low altitude for fun Fabricated by accurate molds with high fidelity of real airplane Excellent stability and aerobatic capability High roll rate Digital Propor |
|
|
4-CH R/c F15E Foam EDF Remote Controlled Jet ARF Version w/ Electric Brushless Ducted Fan + Brushless Motors + ESC + LiPo $169 The F15 Eagle program developed the current generation air superiority fighter for the United States Air Force to counter emerging worldwide threats. It is designed to penetrate enemy airspace and achieve a first-look, first-kill capability against multiple targets. The F15 Eagle is characterized by a low-observable, highly maneuverable airframe; advanced integrated avionics; and aerodynamic performance allowing supersonic cruise without afterburner. This F15 Eagle holds the same beautiful lines as the original fighter jet. The wing and body used in this jet are specially designed to allow high G maneuvers, yet the wing loading is still very low. It becomes a stable aircraft with excellent performance. Receiver-Ready Version (no transmitter and receiver) Specification: Wingspan: 740mm (29.2 in) Length: 1070mm (42.2 in) Flying Weight: 650g (22 oz) Drive System: EDF64 Ducted Fans with Brushless Motors Servo: 5 X 8g high speed micro servos Speed Controller: 25 amp Brushless Speed Control Battery: 11.1V 2100mah Li-Polymer Control system: 4 CH Multifunctional FM Radio Transmitter and 6 CH Micro Receiver Radio Control Range: > 1000 feet (300m) Feature: 4 Channel Full Function Radio Controlled (Aileron, Elevator, Rudder, Throttle) 4 Channel Digital Proportional FM PPM High Quality and Performance Futaba Compatible Radio System Full aerobatic characteristics; inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are possible The wing and body used in this jet are specially designed to allow high G maneuvers, yet the wing loading is still very low Powerful ducted fans with brushless motors makes it possible to fly this plane at high speed in the situations with much wind Excellent stability of nosing up and down One of the best ducted fan jet in the market! State of the art components such as EDF64 Ducted Fans with Brushless Motors, 25amp Brushless Speed Control, and 2100mAh 11.1 V Li-Po Battery Pack Steerable nose landing gear Rudder helps steer plane on ground on its scale landing gear for easy take off Ready to Fly in Just Minutes! Super tough, lightweight airframe! Perfect appearance and emulation (Scale appearance, great attention has been given to details) Shock Resistant Reinforced Fuselage and Strong Wings Can Take Off From Ground or Hand Launched Ground Take-Off can be performed easily Excellent Flight Performance Super easy and super stable electric powered scale R/C park flyer for beginner or middle- |
|
|
11 Pcs RC Tool Kit w/ Handy Case $89.95 11 Pcs RC Tool Kit w/ Handy Case Tool Kit Contents: 1 x Hook 1 x 1.5mm Hexangular Screwdriver 1 x 2.0mm Hexangular Screwdriver 1 x 2.5mm Hexangular Screwdriver 1 x 3.0mm Hexangular Screwdriver 1 x Long Nose pliers 1 x Cutter Pliers 1 x + 1#Screwdriver 1 x - 1#Screwdriver 1 x 7.0mm Hexagonal socket 1 x 5.5mm Hexagonal socket Great tool for all RC hobby! The perfect tools for RC Heli Pilots! |
|
|
12 Pcs RC Tool Kit w/ Handy Case $99.95 12 Pcs RC Tool Kit w/ Handy Case Tool Kit Contents: 2 x 1.5mm Hexangular Screwdriver 1 x 2.0mm Hexangular Screwdriver 1 x 2.5mm Hexangular Screwdriver 1 x Ball Link Pliers1 x Long Nose pliers 1 x Cutter Pliers 1 x + 1#Screwdriver 1 x - 0#Screwdriver 1 x + 0#Screwdriver 1 x 4.0mm Hexagonal socket 1 x 5.5mm Hexagonal socket Great tool for all RC hobby! The perfect tools for RC Heli Pilots! |
|
|
Exceed RC 3-Channel J3 Piper Cub EP Electric RC Airplane 100% Ready-to-Fly *New* THE BEST TRAINER!!! $119 Exceed RC's SD J3 Grasshopper Scale RC Plane 1:10 SCALE READY TO FLY Electric Powered RC Airplane, Brand New! Ready to fly RC with amazing performance. Complete with 3 channel C&F RC, 9 gram micro servos, rechargeable battery and charger installed. Even the pushrods and control surface horns are fitted! Factory built. Just takes minutes to assemble. You can even remove the RC and use it in other models! What a great investment in fun!! Piper Cub J3 Beginners Guide Part 1 ' Piper Cub J3 Beginners Guide Part 2 The J3 CUB 3 Channel has successfully trained thousands of newbie radio controlled pilots worldwide. You'll be flying within minutes of receiving this fully built airplane enjoying over 12 minute flight times on a single charge thanks to our new improved NiMH battery and ball bearing gear drive system. Equipped with a powerful speed electric motor, which starts with a push of a button, the J3 CUB is capable of take-offs from the ground with its huge powerful motor and wide wingspan. Battery Operated 380 Motor Plane Ready to Fly, assembly can be done in 10 mins Digital Proportional Speed Controller Slow Speed Flying Capable, Good for Beginner Shock Resistant Reinforced Foam Fuselage and Strong Wings 2 X 18g micro servo for Rudder and Elevator Control R/C Set included, Complete 3 Channel Control including Complete Left/Right Control by Rudder Complete Elevator Control Digital Proportional Motor Speed Control Knob Superb Quality--Simply The Best RTF Plane you can find Up to 300Maltitude, over 15 mins flight time Powered by 8.4V NIMH re-chargeable battery (110v adaptor included) Can Fly as a Glider (without Motor Power) Brand NEWAll tools required are included for you Assembly take less than 20mins Best Looking Plane on the market Data Sheet: Ready to fly (RTF) with battery charger and RC! Includes REAL RC equipment which can be used in other models! Wing span - 37.5 inches (95.5cm) Length - 28.8 inches (73cm) Wing area - 13.7dm2 Assembly is a snap! With no tools required, you can be up and flying within minutes of opening the box! Highlighted features for this airplane Transmitter 3 Channel Radio Controller features: Left/Right Control Elevator Control Digital Progressive Motor Speed Control Kno |
|
|
RC Lander Hawker Hunter 70mm EDF RC Jet w/ Retractable Landing Gear $449.95 RCLander Hawker Hunter 70mm RC Electric Ducted Fan EDF Jet Features RCLander Hawker Hunter 70mm RC Electric Ducted Fan EDF Jet Precision Molded EPO Airframes With Outstanding Detail & Scale Appearance Full set door system Perfect for all levels: beginners, middle-level users, or experienced pilots. Beautiful design and great details: resembling real plane Factory-finished for aggressive fighter jet appearance. Construction: Lightweight, strong, and crash resistant. Easily take off: can depart from either ground or hand effortlessly. Powerful ducted fans with brushless motors and brushless ESC and strong wing designed for smooth airflow: providing exceptional stability, and great ease to control and fly even with wind Full function control of the plane: Throttle, Aileron control, Rudder, Elevator, flaps, Door operate System Fuselage: Durable pre-colored foam fuselage, wings and tail Specifications Wingspan: 1050mm / 41.3" Length: 1000mm / 39.3" Weight: 1000g/38.8oz to 1500g/52.9oz Power system: Single 70mm EDF ESC: 60A or above Functions: Throttle, Aileron control, Rudder, Elevator, flaps, Door operate System Servo: 9g X 8 Battery: 14.8V 4S 2250mah or higher Li-Polymer Radio: 6CH Package Contents RCLander Hawker Hunter 70mm RC Electric Ducted Fan EDF Jet User Manual What you need to Complete 6CH Channel Transmitter Compatible receiver Motors Servos ESC Ducted Fan Unit Lithium-polymer battery Requires: Brushless Motor, Controller, LiPo, Servos, Receiver & Transmitter Battery: 4S-2500, 4S-3300 or 4S-3700 |
|
|
Exceed RC Mirage 2000 64MM EDF Jet * Receiver-Ready Version * $299.95 This is a Receiver-Ready Mirage 2000 64MM EDF Jet. User is required to have their own TX+RX. Wingspan: 575mm Length: 830mm Flying Weight: 520g Three 9 gram servos Brushless Powered: Powerful 14L inner runner brushless motor and 25A ESC Battery: 3 Cell Li-Po Battery,1300 mAh,11.1V Additional Requirements: Radio System: 4Ch Tx and 6 Ch Rx, Exceed RC has now shrunk this fighter jet so you can fly at your own hands. The Exceed Rc Mirage 2000 Lighting Red Series is made with high performance Ducted Fan, Receiver-Ready right out of the box with minimum assembly required. Exceed RC Mirage 2000 is powered by the new developed 14L inner runner brushless motor with 25A ESC electric speed controller. The Exceed RC Mirage 2000 Lighting Red Series RTF Scale Jet is an all-molded foam airplane that comes completely painted in an attractive matte finish with waterslide decals applied. The 64mm fan with brushless inner runner motor is pre-installed, as is the 25A brushless speed control. The jet has 3 preinstalled servos. Landing gear is fixed but can be easily removed for hand launching. Battery changes are quick, just remove the hatch and place it in. The Exceed RC Mirage 2000 jet is large enough for good visibility in flight, but is easily transported. The thrush from the 64mm fan with the included 3 cell Li-po Battery 1300 mAh 11.1V will quickly accelerate the Exceed RC Mirage 2000 Jet into the air. The climb out is steep and the speed impressive. The full scale Mirage 2000 had the glide angel of a brick; our version display much more pilot friendly manners. Due to its light weight, the Mirage 2000 flying character, making landings a thing of beauty. Flight times are about 10 on a charge. |
|
|
Extreme Detail 4 Channel Air Field RC Skyline 182 - 55" Trainer Radio Remote Control Airplane w/ Brushless Motor/ESC/Lipo 100% RTF *Super Scale* EPO Foam P $399.95 Get ready to go from the box to the sky in just minutes with the new Air Field RC Sky Trainer. This plane is made for users of all levels. Ready to fly (RTF) with all electronics pre-installed and life-like designs, this plane will soar through the sky, even in windy conditions. Do 3D aerobatic maneuvers made capable with the powerful brushless out runner motor. It?s light-weight, strong, and made with crash resistance in mind. Super scale. Beautiful plane. Easy to fly. High Quality! You will not be disappointed! This 4 Channel EPO Foam Skyline 182 Airplane is ready to fly and is made of EPO shock resistant foam material which is stronger than those made of other foams. Features Perfect for all levels: Beginners, Middle-level users, or Experienced Pilots RTF: Ready to Fly right out of the box (Everything included and 90% assembled) Easy to construct with pre-installed electronics (motors, servos and speed controllers) Beautiful design and great details: Resembles a real plane Factory-finished with stunning appearances 3D Aerobatic Performance Construction: Lightweight, strong, and crash resistant Easy take off: effortlessly depart from the ground or your hand Powerful Brushless Outrunner Motor (700kv) and 25A Brushless ESC Strong wing designed for smooth airflow providing exceptional stability, and great ease to control and fly even in wind conditions Full function 4 Channel Futaba compatible transmitter with mixing: Aileron control, Elevator control, Rudder, and Throttle. Durable pre-colored foam fuselage, wings, and tail Expert-designed propellers and steer-able front landing gear Battery: High Quality Rechargeable 11.1V 1800mah Li-Polymer Battery for 20 minutes flight time (Upgradeable optional battery for even longer flight time). 90 Minutes auto peak detection charger 25Amp Brushless Electronic Speed Controller Specifications Wingspan: 55.5in/1410mm Overall Length:40.5in/1030mm Flying Weight: 1100g Wing Area: 27.35dm² Wing Loading: 34g/dm² Drive System: Brushless Outrunner Motor (700kv) Servo: 4X 9g High Speed Micro Servos Speed Controller: 25A Brushless ESC Battery: 11.1V 1800mAh Li-Poly Control System: 4 CH Multi-functional FM Radio Transmitter and 6 CH Micro Receiver Radio Control Range: 3000 Feet (1000m) Package Contents Air Field RC Sky Trainer 4CH Remote Control Electric Plane w/ Brushless Motor LiPo RTF 4CH Transmitter (Left Hand Throttle ? Mode II, 72MHz) Receiver, Brushless and ESC LiPo Battery Balance Charger 11.1V 1800mAh Li-Poly Rechargeable Battery Propeller and Landing Gear English User Manual If you are thinking about joining this great hobby, consider the SkyTrainer as your first trainer. Get some help and you will get even more out of radio control flying. With the SkyTrainer you have a stable platform to learn to fly, and it all comes in one kit tha |
|
|
Brand New 3 Channel RC RTF EP 35? Aerobatic Barracuda Scale Remote Control Plane (Blue) $74.95 Brand New 3 Channel RC EP 35? Aerobatic Barracuda Scale Remote Control Plane. This package comes with 3 sets of propellers, spinners, glue and full set of hardware. Its a RTF plane so no need for anything else. It is capable of stunt flying and air show tricks, suitable for experienced flyers as well as beginners. Features: Super strong gauge foam fuselage and wings.Made of EPO shock resistant material.Excellent flying performance.Easy to assemble.Easy to fly.Ideal for Beginners. Specification:Length : 750mm (29.52")Wing span : 890 mm (35.04")Main Wing Area : 13.6 dm²Flying Weight : 480gMotor 370A with GearBoxPropeller : 8 X 6"Battery : 9.6V 650mAhRadio : FM4-Channel proportional radio w/ V-Type mixed controller Items included: 3 Channel RC EP Barracuda Scale PlanePropeller * 3GlueDecalsScrew DriverScrews and hardwareUser Manual |
|
|
Exceed RC F-4E Phantom ARF 64mm EDF RC Jet (without Transmitter & Receiver) $249.95 F-4E Phantom Electric Ducted Fan Radio Control Jet ALMOST-READY-TO-FLY-VERSION WITHOUT TRANSMITTER+RECEIVER Factory Flight Test F-4E Review & Flight Features: -State of the Art Foam -Fully Proportional Elevator, Rudder and Throttle Controls -Improved Aerodynamic with innovative Wing and Fuselage Design -Durable Fuselage and Wings Construction -Easy to learn for Beginner and Fun to Fly for Experts This is the latest creation from the fertile mind of genius EDF designer Andy Chen...there IS a difference as to who designs these, this guy just has the magic touch, and it shows in the scale accuracy of the overall plane, and also in a lot of thoughtful little details and engineering that really make it stand out from the competition. It's beautiful! Small, and very high performance...Very high quality molding, lots of detail, good paint, good water transfer decals, clear canopy with cockpit deck(the pics on the nitroplanes website show an early prototype with a tinted canopy), easily removeable or replaceable landing gear, full flying stab, easy fan access for maintanance, lots of nice features. In the air, it's pure dynamite, everybody guesses it to be about 70mph, and that's very fast for such a small airplane! It's a whole level of performance above the rest of the RTF EDF jets... It's basically the smallest airframe that you can wrap around a 64mm fan. Hand launching is really easy, there is a grip molded in for doing it, and you don't need to heave it, it will fly away from just a light toss with no problems. Roll rate is tremendous, vertical performance is awesome, and downright speed, well...most EDFs, you fly around at full bore all the time, with this one, you want to save full throttle for verticals and high speed passes, and throttle back to half or two thirds to keep the thing manageable the rest of the time, it's mighty quick. It's very easy to land, I have been bellying mine in on the grass with no problems, though you might want to put a little glass cloth on the lower lip of the intakes, they tend to snag the grass and get chipped up. With the landing gear on, off pavement, it has no bad habits at all. The gear comes on and off with a few screws in a minute or two. It takes up no room in the car, it can fly out of small parks, or you can take it to the club field and mix it up with the big boys, it costs little, it requires no maintainance, it looks great, and it flies great. It's my new favorite airplane! Wingspan: 542mm Length: 788mm Flying Weight: 540g Wing Area: 8dm^2 Wing Load: 67g/dm^2 64mm Ducted Fan Servos : 4 9G Servos Motor : 14L inner brushless motor ESC : 25A Battery : 11.1V 1300mAH LiPo Battery Radio System REQUIRED : 4-Channel TX and 6CH Rx |
|
|
Exceed RC F-4E Phantom ARF 64mm Electric Ducted Fan RC Jet Shark Version (without Transmitter & Receiver) $249.95 F-4E Phantom Electric Ducted Fan Radio Control Jet ALMOST-READY-TO-FLY-VERSION WITHOUT TRANSMITTER+RECEIVER Factory Flight Test F-4E Review & Flight Features: -State of the Art Foam -Fully Proportional Elevator, Rudder and Throttle Controls -Improved Aerodynamic with innovative Wing and Fuselage Design -Durable Fuselage and Wings Construction -Easy to learn for Beginner and Fun to Fly for Experts This is the latest creation from the fertile mind of genius EDF designer Andy Chen...there IS a difference as to who designs these, this guy just has the magic touch, and it shows in the scale accuracy of the overall plane, and also in a lot of thoughtful little details and engineering that really make it stand out from the competition. It's beautiful! Small, and very high performance...Very high quality molding, lots of detail, good paint, good water transfer decals, clear canopy with cockpit deck(the pics on the nitroplanes website show an early prototype with a tinted canopy), easily removeable or replaceable landing gear, full flying stab, easy fan access for maintanance, lots of nice features. In the air, it's pure dynamite, everybody guesses it to be about 70mph, and that's very fast for such a small airplane! It's a whole level of performance above the rest of the RTF EDF jets... It's basically the smallest airframe that you can wrap around a 64mm fan. Hand launching is really easy, there is a grip molded in for doing it, and you don't need to heave it, it will fly away from just a light toss with no problems. Roll rate is tremendous, vertical performance is awesome, and downright speed, well...most EDFs, you fly around at full bore all the time, with this one, you want to save full throttle for verticals and high speed passes, and throttle back to half or two thirds to keep the thing manageable the rest of the time, it's mighty quick. It's very easy to land, I have been bellying mine in on the grass with no problems, though you might want to put a little glass cloth on the lower lip of the intakes, they tend to snag the grass and get chipped up. With the landing gear on, off pavement, it has no bad habits at all. The gear comes on and off with a few screws in a minute or two. It takes up no room in the car, it can fly out of small parks, or you can take it to the club field and mix it up with the big boys, it costs little, it requires no maintainance, it looks great, and it flies great. It's my new favorite airplane! Wingspan: 542mm Length: 788mm Flying Weight: 540g Wing Area: 8dm^2 Wing Load: 67g/dm^2 64mm Ducted Fan Servos : 4 9G Servos Motor : 14L inner brushless motor ESC : 25A Battery : 11.1V 1300mAH LiPo Battery Radio System REQUIRED : 4-Channel TX and 6CH Rx |
|
|
CMP P40 Warhawk 50 - 54" Nitro Gas ARF Radio Remote Controlled RC Airplane RC "Tiger Shark" Plane $299 This P40 Warhawk has a fiberglass fuselage and cowl painted in vague colors. The rib wings are covered with Solartex and airbrushed to match the color of the whole aircraft. The wood that makes up both the wings and the fuselage are all laser cut. The high precision of fiberglass and fine painting work make this kit an extremely realistic aircraft. It is a perfect combination between scale looks and excellent flying performance. The kit comes with a full color decal sheet, wheels and a fuel tank. This war bird is a must fly! What the Pro says! Just to clear up some confusion, and a lot of misinformation on the internet...CMP is not Willhobby, or FlyModel, or any other company. CMP is thier own company, and they have been around for while. I have built a few of their planes, and found the quality to be quite exceptional, they are high-end stuff, and from a scale point of view, nobody else comes close. The P-40, from a scale aspect, blows away the Hangar 9 and everybody else's P-40. The paint job is dead flat and perfect, and there are a ton of factory-installed water transfer decals, a beautiful glass belly tank, strut covers, prepainted canopy frame, lots of nice stuff. All the hardware is exceptional, too, with a fiberglass pushrod for the elevator, and a pull-pull system for the rudder. You need to be careful flying it, though. It has no washout, it's not light, and it will tip stall if you pull too hard or get too slow. The big problem, though, is that the CG in the manual is actually for the much larger 71" one, and will leave you very tailheavy if you don't correct it to about 85mm from the LE. It's really, really important. If you fly off grass, you will have really hard time finding rotating retracts that will hold up. Seriously consider fixed gear like I used. I flew mine with a Saito 62, fit perfectly and was plenty of power. Let's here some other comments, this is a beautiful plane.. For more reviews and comments on other NitroPlanes.com products by rc enthusiasts, click here. *RETRACT NOTE* The retract bays are built into the wing from the factory, so the retracts will drop right in. Wing Span: 53.5" Weight: 5.64lb Length: 46" Wing Loading: 26.97oz./sq.ft. Wing Area: 480sq.in Engine 2c 40~46, 4c 52~63 Radio 4~5 Channel 5~6 Servos The kit box is nice packed, with all the major parts well packed in a light foam wrap and clear plastic bags. All wood rib wing, nicely covered, rivets decals already applied, ailerons hinged and installed. Horizontal, elevators and rudder also all wood, air foiled surfaces, hinged and ready. Fuselage is very detailed with panel lines molded in, glass work is outstanding. Tiger mouth decal, dashboard decal and many others perfectly applied. Drop tank included and assembled. Slots in the interior cardboard held all items tightly |
|
|
4-Channel F15E RC 64mm EDF Foam Jet RTF Version With Radio (Gray) ( Includes Electric Brushless Ducted Turbo Fan + 25A ESC + LiPo Battery 100% Ready-to-Fly ) $499 The F15 Eagle program developed the current generation air superiority fighter for the United States Air Force to counter emerging worldwide threats. It is designed to penetrate enemy airspace and achieve a first-look, first-kill capability against multiple targets. The F15 Eagle is characterized by a low-observable, highly maneuverable airframe; advanced integrated avionics; and aerodynamic performance allowing supersonic cruise without afterburner. This F15 Eagle holds the same beautiful lines as the original fighter jet. The wing and body used in this jet are specially designed to allow high G maneuvers, yet the wing loading is still very low. It becomes a stable aircraft with excellent performance. RTF (100% Ready To Fly) Version with transmitter and receiver Click Here to Buy the ARF-Version (w/out Transmitter +RX) What the Pro says! This F15 plane is absolutely outstanding, particularly on two fronts...fly ability and scale appearance. What's in the box? Motor and 64mm fan and 25a ESC, already installed. Five servos, already installed. 2200mah lipo battery. A very useable balance charger that will peak and balance the battery to 12.6v exactly, just like my expensive charger does. A screwdriver, a package of good quality five minute epoxy. All hardware and landing gear. All foam components prepainted and predecorated. A canopy with the frame painted on. Everything you need except a transmitter and receiver. Construction took about 45 minutes, with no problems and no surprises. Do check the fit of the foam parts, and sand away any paint where you are gluing. Keep in mind that both elevator control horns need to point towards the same side of the aircraft, so the elevators go up and down together. The main gear gets glued into place...there is no real easy way to change that(maybe with some plywood plates?), so you need to make the choice of either gear up or gear down and live with it. I got one and flew it with the gear on, and was so pleased that I ordered a second one so I could have another with the gear off for hand-launching over grass. Frankly, there is not much to say about building it, it's dead simple to get together. So...off to the field. First takeoff took about 100 feet. It was obvious that it was at flying speed long before that, and that the slightly negative angle of attack from the small nosewheel was keeping the plane down, and I needed to apply elevator to get it off the ground. I suspect the designers did this deliberately, to make sure that beginning pilots would have adequate speed to avoid a slow takeoff and tipstall. If you put on a bigger nosewheel or bent the main gear forward a bit, it would take off a |
|
|
AirField 70MM Brushless F-16 Electric Ducted Fan (EDF) Radio Remote Controlled Jet Sky Grey w/ Bombs RTF $399.95 This 70mm F-16 Fighter is a high quality EPS foam model of the famous ?Fighting Falcon?. The F-16 is known as the ?Viper? in US service. It was the first fighter designed to sustain 9g maneuvers. One of the outstanding features is its frameless bubble canopy, which gives excellent all-round vision. The F-16 has been and will remain the multi-role workhorse of the United States Air Force. The F-16 was the main fighter used in the 1991 Gulf War and is still used in today?s ?War on Terror?. The Air National Guard regularly deploys these fighters to the Middle East. In honor of the US Fighters, it is only appropriate that we built these jets with extra care and fine detail. It is painted with an excellent finish to make it look just like the real thing. No details were left out, from the after burner, the missiles, to the predominant nose. To do the F-16 justice, we used the newest electronics and gave it the U.S. Air Force look. Even though we went out of the way to mirror the real F-16, this EDF Jet was also built to be user friendly and ready to fly. The fuselage is pre-assembled and it requires very minimal assembly to get it soaring in the sky. 4 Channel Full Function Radio Controlled (Aileron,Elevator,Rudder,Throttle) Full aerobatic characteristics; inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are possible Excellent hedgehopping performance High speed, flying speed at 80mph+!!! Excellent stability of nosing up and down State of the art components such as Outrunner Brushless Ducted Fan, 45amp Speed Control, and 2200mah 20C 14.8 Volt Li-Po Battery Pack famousus "Cobra Maneuver" available Steerable nose landing gear Rudder helps steer plane on ground on its scale landing gear for easy take off Super tough, lightweight airframe! Shock Resistant Reinforced fuselage and Strong Wings Can Take Off From Ground or Hand Launched Ground Take-Off can be performed easily Excellent Flight Performance Super easy and super stable electric powered scale R/C park flyer for beginner or middle-level users Stable inverted flight fuselage with pre-installed Electronics, Motor, Servos, and Speed Controller Superb Quality, Simply the Best RTF Jet you can find!!! Super stable for beginner, Super low speed for safety, Super low altitude for fun Fabricated by accurate molds with high fidelity of real airplane Excellent stability and aerobatic capability High roll rate Dig |
|
|
4-CHANNEL EP-Powered AT-6 Texan RC AIRPLANE Model Kit (Unassembled) $49.95 Features: 4 Channel Remote Control Airplane Full aerobatic characteristics; inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are possible Constructed with Super Tough, lightweight EPO material! Perfect appearance and emulation (Scale appearance, great attention has been given to details) True Classic Trainer of All Time! Decorative Waterslide Decals! Easy to Build & Endless Fun to Fly! Perfect Low-Wing Trainer! Rudder helps steer plane on ground on its scale landing gear for easy take off Shock Resistant Reinforced fuselage and Strong Wings Can Take Off From Ground or Hand Launched Ground Take-Off can be performed easily Huge Wing size, Excellent Flight Performance Super easy and super stable electric powered scale R/C park flyer for beginner or middle-level users Stable inverted flight Super stable for beginner, Super low speed for safety, Super low altitude for fun Fabricated by accurate molds with high fidelity of real airplane Excellent stability and aerobatic capability Detailed Body Structure High roll rate Super low speed for safety, Super low altitude for fun Crash Resistant Construction Easy to Fly, Easy to Control, Super stable for beginner Slow Speed Flying Capable, Good for Beginner Suitable for both beginners and experienced pilots Specifications: Wingspan: 900mm (35.4") Length: 680mm (26.7") Flying Weight: 480g (16.9 oz) Requirements: Drive System: 370 carbon brushed motor Servo: 3X 9g high speed micro servos ESC: 20A speed controller Battery: 9.6V 650mah Ni-MH Control system: 4 CH Multifunctional Radio Transmitter and Receiver Included: Airplane Kit Unassembled Screw Driver 4 Propellers English Manual |
|
|
Air Force One Radio Remote Controlled 2-Channel RC Plane RTF $149.95 This plane has realistic look. It is form constructed on fuselage and wings. Some portion have plastic joints to enhance the durability. There are two propellers hidden in the engine cabinets on the main wing. So you might guess it is a jet plane when you see it first time, but figure out is only a electric motor powered airplane later. It is clean and easy to assemble. The package comes everything you need except 8xAA batteries for remote controller. Features * Simulating a true style * All molded plastic and foam construction * Precision Control Specification * Operation Distance 100m * Fly Time 3 minute * Rapidity Electrification 30 minute * Length: 70cm * Width: 70cm Package Included * Air Force One Airplane * 9.6V 400mAh Ni-Mh Rechargeable Battery * 2 Channel Transmitter * AC Charger * English Manual |
|
|
Brand New 4 Channel RC EP 37.0? Aerobatic Do-335 Dornier Pfeil Twin Dual Engine EPO Foamy RTF Scale Plane (Green) $199.95 Brand New 4 Channel RC EP 37.0? Aerobatic Do-335 Dornier Pfeil Twin Engine EPO Foamy RTF Scale Plane. This package comes with 3 sets of propellers, spinners, glue and full set of hardware. Its a RTF plane so no need for anything else and with dual motor that power your flying time twice as fun. It is capable of stunt flying and air show tricks, including inside and outside loops, cuban 8, invert fight, roll ,etc suitable for experienced flyers as well as beginners. Features: Super strong gauge foam fuselage and wings.Made of EPO shock resistant material.Excellent flying performance.Easy to assemble.Easy to fly.Ideal for Beginners. Specification:Length : 935mm (37")Wing span : 940mm (37.01")Main Wing Area : 17.8 dm²Flying Weight : 740gMotor :2-370A with GearBoxPropeller : 8 X 6"Battery : 9.6V 1100mAhRadio : FM4-Channel proportional radio w/ V-Type mixed controllerPackage Shipping Weight : 1755gItems included:4 Channel RC EP 37.0? Do-335 Dornier Pfeil RTF Scale PlanePropeller * 3GlueDecalsScrew DriverScrews and hardwareUser Manual |
|
|
Brand New 4 Channel RC EP 37.0? Aerobatic Do-335 Dornier Pfeil Twin Engine EPO Foamy RTF Scale Plane (Black) $249.95 Brand New 4 Channel RC EP 37.0? Aerobatic Do-335 Dornier Pfeil Twin Engine EPO Foamy RTF Scale Plane. This package comes with 3 sets of propellers, spinners, glue and full set of hardware. Its a RTF plane so no need for anything else. It is capable of stunt flying and air show tricks, including inside and outside loops, cuban 8, invert fight, roll ,etc suitable for experienced flyers as well as beginners. Features: Super strong gauge foam fuselage and wings.Made of EPO shock resistant material.Excellent flying performance.Easy to assemble.Easy to fly.Ideal for Beginners. Specification:Length : 935mm (37")Wing span : 940mm (37.01")Main Wing Area : 17.8 dm²Flying Weight : 740gMotor :2-370A with GearBoxPropeller : 8 X 6"Battery : 9.6V 1100mAhRadio : FM4-Channel proportional radio w/ V-Type mixed controllerPackage Shipping Weight : 1755gItems included:4 Channel RC EP 37.0? Do-335 Dornier Pfeil RTF Scale PlanePropeller * 3GlueDecalsScrew DriverScrews and hardwareUser Manual |
|
|
The New AirField 70MM Electric Ducted Fan Jet EDF F4 w/ Missles Brushless ESC/Motor & Lipo Battery (Red) $399.95 This 70mm F-16 Fighter is a high quality EPS foam model of the famous ?Fighting Falcon?. The F-16 is known as the ?Viper? in US service. It was the first fighter designed to sustain 9g maneuvers. One of the outstanding features is its frameless bubble canopy, which gives excellent all-round vision. The F-16 has been and will remain the multi-role workhorse of the United States Air Force. The F-16 was the main fighter used in the 1991 Gulf War and is still used in today?s ?War on Terror?. The Air National Guard regularly deploys these fighters to the Middle East. In honor of the US Fighters, it is only appropriate that we built these jets with extra care and fine detail. It is painted with an excellent finish to make it look just like the real thing. No details were left out, from the after burner, the missiles, to the predominant nose. To do the F-16 justice, we used the newest electronics and gave it the U.S. Air Force look.Even though we went out of the way to mirror the real F-16, this EDF Jet was also built to be user friendly and ready to fly. The fuselage is pre-assembled and it requires very minimal assembly to get it soaring in the sky. 4 Channel Full Function Radio Controlled (Aileron,Elevator,Rudder,Throttle) Full aerobatic characteristics; inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are possible Excellent hedgehopping performance High speed, flying speed at 80mph+!!! Excellent stability of nosing up and down State of the art components such as Outrunner Brushless Ducted Fan, 45amp Speed Control, and 2200mah 20C 14.8 Volt Li-Po Battery Pack famousus "Cobra Maneuver" available Steerable nose landing gear Rudder helps steer plane on ground on its scale landing gear for easy take off Super tough, lightweight airframe! Shock Resistant Reinforced fuselage and Strong Wings Can Take Off From Ground or Hand Launched Ground Take-Off can be performed easily Excellent Flight Performance Super easy and super stable electric powered scale R/C park flyer for beginner or middle-level users Stable inverted flight fuselage with pre-installed Electronics, Motor, Servos, and Speed Controller Superb Quality, Simply the Best RTF Jet you can find!!! Super stable for beginner, Super low speed for safety, Super low altitude for fun Fabricated by accurate molds with high fidelity of real airplane Excellent stability and aerobatic capability High roll rate Digital Proportional Motor Speed Control Easy to Fly, Easy to Control, Super stable for beginner Slow Speed Flying Capable, Good for Beginner Suitable for both beginners and experienced pilots Approximately 10 minutes flight time on each charge - Optional Li- poly battery will help to achieve better performance and longer flight time. All spare parts and accessories are available Ready to Fly, Easy to Assemble (90% assembled ) Wingspan: 780mm (30 |
|
|
|
Cutting Foam 101
